Pni FieldForce Trax Manuel d'utilisateur télécharger pdf (Page 35)

PNI Sensor Corporation DOC#1016505 r06

TRAX User Manual Page 31

Start/Stop Testing

Clicking the <Start> button results in the Heading, Pitch, and Roll values being

updated on the Test Tab screen, as well as the Heading Status.

If the Acquisition Mode is set to “Continuous”, then the data will be continuously

updated. The button will change to read <Stop>, such that clicking it again will stop

the screen from updating.

If the Acquisition Mode is set to “Single”, then only one measurement will be

displayed on the screen. The button will briefly gray out while the data is being

output to the screen, then return to reading <Start>.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 61 62

User Manual 1
Table of Contents 2
TRAX User Manual Page ii 3
List of Figures 4
List of Tables 4
TRAX User Manual Page 1 5
2 Introduction 6
3 Specifications 7
TRAX User Manual Page 4 8
TRAX User Manual Page 5 9
3.2 Mechanical Drawings 10
TRAX User Manual Page 7 11
4 Set-Up 12
4.2 Installation Location 13
4.3 Mechanical Mounting 13
4.3.2 Mounting Orientation 14
TRAX User Manual Page 11 15
5 User Calibration 16
5.1 Magnetic Calibration 17
TRAX User Manual Page 14 18
TRAX User Manual Page 15 19
5.1.2 2D Calibration 20
Footnote: 21
TRAX User Manual Page 18 22
TRAX User Manual Page 19 23
TRAX User Manual Page 20 24
6.1 Installation 25
TRAX User Manual Page 22 26
6.4 Configuration Tab 27
6.4.1 General Settings 28
6.4.2 Acquisition Settings 29
TRAX User Manual Page 26 30
6.5.1 Calibration Settings 31
TRAX User Manual Page 28 32
6.5.3 Calibration Results 33
6.6 Test Tab 34
TRAX User Manual Page 31 35
TRAX User Manual Page 32 36
6.7 Log Data Tab 37
6.8 Graph Tab 38
6.9 System Log Tab 39
7.1 Datagram Structure 40
7.2 Parameter Formats 41
7.2.3 Signed Integer 42
7.2.4 Unsigned Integer 43
7.2.5 Boolean 43
7.3 Commands Overview 44
7.4 Set-Up Commands 45
Config ID 46
TRAX User Manual Page 43 47
TRAX User Manual Page 44 48
(Config. ID 19 49
7.5 Measurement Commands 50
AcquisitionMode: 51
FlushFilter: 51
PNIReserved: 51
SampleDelay: 51
7.5.3 Data Components 52
(Component IDs 5 53
(Component IDs 79 53
7.5.4 Making a Measurement 54
7.6 Calibration Commands 55
Limited-Tilt Calibration 56
Accel-Only Calibration 56
7.6.3 Calibration Score 57
7.6.4 Factory Calibration 58
7.7 Compass Mode Commands 59
7.7.2 FIR Filters 60
TRAX User Manual Page 57 61
Payload 61
7.7.3 Power Down/Up 62

Commentaires sur ces manuels

Pas de commentaire

Pni FieldForce Trax Manuel d'utilisateur Page 35

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Pni FieldForce Trax